Practical answers on choosing, powering and safely using battery-powered angle grinders for metalwork.
Why must the guard stay fitted, and is it adjustable?

The guard sits between you and the rotating wheel. It is there to stop fragments if a wheel breaks, to limit accidental contact with the wheel, and to deflect sparks. It must be securely attached and set so that it is between the wheel and the user, with the least amount of wheel exposed towards you. HSE guidance warns that unguarded wheels have caused serious and sometimes fatal accidents.
Most guards can be rotated to suit the direction of the work, and some need a different guard for cutting. Always tighten the clamp after adjusting. If a guard is cracked or damaged, replace it rather than use it. Use only a guard that the manual lists for your model and disc size.
Can I grind with a cutting-off disc, and cut with a grinding disc?

No, use each disc for what it was designed for. Cutting-off discs are thin and designed to cut with their edge, so grinding on the flat side puts side load on them and they can shatter. Cutting with a thicker grinding disc is also unsuitable because it is not designed for it, and it binds in the cut.
For hand-held machines, cutting-off wheels should be the reinforced type. HSE guidance says an unreinforced cutting-off wheel should never be used on a portable grinding machine. Some grinders need a different guard for cutting, so check the manual. If you do both jobs regularly, keep suitable discs for each and swap them as needed.
How do I choose the right disc and check it is safe to use?

Match the disc to the job and to the machine. Check that the wheel is intended for hand-held grinders, that its diameter and bore suit the machine, and that its rated speed is at least the grinder's maximum speed. Look at the wheel before every use and do not use one that is chipped, cracked or damaged. HSE guidance says bonded abrasive wheels for hand-held use carry a use-by date of three years from manufacture, so do not use out-of-date ones, and store them dry, with thin discs kept flat.
Have wheels fitted by someone who has been trained to do it. HSE says a new wheel should be run free at full operating speed for a short period, with the guard in place and everyone standing clear; grinder makers commonly specify one minute at full no-load speed. Always wear eye protection.
What is kickback and how do I reduce the risk?

Kickback is a sudden reaction when the wheel snags or is pinched in the work. The wheel stalls and the tool is thrown in a direction opposite to where the wheel was turning at the pinch point. It can happen in an instant, and it is a leading cause of injury with angle grinders.
Keep a firm grip with both hands, and position your body and arm so you can resist the force and so you are not in line with the path the tool would take. Do not restart a cut while the wheel is still in the workpiece: let it reach full speed and re-enter carefully. Support large or loose workpieces so they cannot sag and pinch the wheel. Never lay the machine down until the accessory has stopped completely.
How can I reduce vibration and fatigue when grinding?

Regular hand-held grinding exposes your hands and arms to vibration, and over time this can cause permanent damage. HSE guidance advises choosing lower-vibration equipment where there is a suitable alternative, checking vibration figures in the handbook or sales literature, keeping tools maintained as the maker instructs, and planning work to limit the time you hold vibrating tools. The HSE notes that tool selection can make a substantial difference, provided the tool is suitable for the task.
Use the side handle, avoid gripping harder than you need to, and keep your hands warm. Anti-vibration handles and the right accessories can lower vibration, and finishing a job faster can sometimes reduce total exposure. Let the disc do the work instead of pushing, and take regular breaks. Tingling or numbness in the fingers is a key symptom, and the HSE says workers need to report early symptoms to their employer.
What does 'bare unit' mean, and which battery and charger do I need?

A bare unit is the tool on its own, without a battery or charger. It suits you if you already have compatible batteries from the same maker's range; otherwise you will need to get a battery and charger separately. Battery platforms are usually specific to the maker and sometimes to a voltage, so check the compatibility details in the manual or ask the manufacturer first.
Use only the battery packs designated for your tool, and recharge only with the charger the manufacturer specifies, because the wrong charger can cause overheating and increase the risk of fire. Fire services advise against charging batteries overnight or leaving them charging unattended, unplugging once fully charged, and stopping use of any battery that is swollen or damaged.