Practical answers on choosing and using 18 V cordless drill/drivers for metalwork, tapping and screwdriving.
Can I tap threads with a cordless drill/driver?

Yes, provided the drill has a low-speed gear and you take care. Drill the core hole to the size given in a thread table for your thread, use a good quality tap suited to the material (HSS taps are normally used for steel, copper and aluminium), and apply cutting oil or a thread cutting oil to cut friction and heat.
Start at low speed with even pressure and let the tap do the work rather than forcing it. Larger threads generally call for the lowest gear, and tapping heads or similar accessories can make the job easier and more controlled. Back the tap out now and then to clear swarf, and check the maker's manual for the largest thread your drill is intended to tap.
What does the clutch do, and how do I set it?

The clutch is the numbered collar behind the chuck. In screwdriving mode it limits the torque applied, and the drive disengages with a clicking sound once the set torque is reached, which helps prevent overdriving screws or snapping small fasteners. Lower numbers give less torque and higher numbers give more.
A sensible method is to start low and work upwards on a scrap piece until the fastener seats properly. The drill symbol on the collar bypasses the clutch so the tool gives its full torque, which is the setting for drilling holes. Remember the clutch is a guide rather than a precision torque tool, so use a proper torque wrench where a specified tightening torque matters.
What do the different gears or speed ranges mean?

Multi-speed drill/drivers have a gearbox that trades speed for torque. The lowest gear gives high torque at low speed and suits heavy-duty work such as large drill bits, hole saws, tapping and driving big fasteners. Higher gears give faster rotation and lower torque for smaller drill bits and light work.
As a rule, bigger diameters need slower speeds, and tough materials such as stainless steel need slower speeds than mild steel. Only operate the gear selector when the tool is not running, because shifting while it turns can damage the gearbox, and push the selector fully home. The manual and data plate give the speed ranges for your tool.
Can a cordless drill/driver cause hand-arm vibration problems?

Any hand-held power tool can contribute to hand-arm vibration if it is used for long periods, and drills are among the tools the HSE covers. Your employer should assess the risk, so choose lower-vibration tools where they suit the job and compare the declared vibration figures in the instruction manual.
Good habits help: keep the tool and bits in good condition, avoid awkward postures that make you grip harder, take the weight of the tool where you can, and limit the time with your finger on the trigger. Warm gloves help keep hands warm but are not a vibration control. Report tingling, numbness or fingers turning white to your employer.
How should I charge and look after the battery?

Use the charger supplied with the battery or one the manufacturer recommends. The wrong charger can overload a battery and raise the risk of overheating and fire. Unplug the charger once the battery is full rather than leaving it on continuous charge, and do not leave batteries charging unattended or overnight.
If a battery has been dropped, or shows overheating, swelling or other damage, stop using it, do not charge it, and dispose of it safely. Keep charging areas clear of escape routes and flammable materials. Your risk assessment and the manufacturer's instructions cover storage and transport rules for your workplace.
How do I drill stainless steel without ruining the bits?

Stainless steel work hardens when heat builds up from the wrong speed or from rubbing, so the aim is to keep the bit cutting. Use a sharp bit made for tough metals (cobalt bits are commonly used because the cobalt runs right through the bit), a low speed, steady feed so you see continuous chips, and plenty of cutting oil or coolant. Do not let the bit dwell or rub in the hole, and stop regularly to re-apply oil if you cannot keep it flooded.
For larger holes it often helps to start with a smaller hole and step up. A blunt bit pushes you to press harder and generate more heat, so replace or resharpen bits as soon as they stop cutting freely. Exact speeds depend on the grade and bit size, so check the bit maker's guidance.