WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 31324000452  

    FEIN Recip Saw Blade for Metal, BIM 205 T8/10 MS (Pack of 3)
    31324000452

    £19.58  EX VAT
    SSP Suggested Selling Price = £24.94  YOU SAVE £5.36

    Sabre saw blade for metal.

    Suitable for use in the following materials: Metal of between 4 and 12 mm, profiles with thick walls as well as timber containing metal residue. Has an impressive extra strong, robust blade with milled, set teeth and a long service life for straight, forceful and coarse cutting. Especially for rescue and demolition work and ideal for use with pipe retainers.

    Specification

    Material: BiM(BiMetal)
    Width: 1.57mm
    Length: 225mm
    Height: 22mm
    Max. material thickness: 12mm
    Min. material thickness: 4mm
    Cut length: 205mm
    TPI: 8 / 10

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    Related Items

    FEIN ABAS 18-21 K AS Saw Blades FAQs

    Answers to common questions about choosing and using reciprocating saw blades for metal and wood.

    How do I choose the right number of teeth per inch (TPI) for metal?icon-minus-redicon-plus-red

    The general rule of thumb from blade makers is that the thicker the material, the lower the TPI. Thin sheet, tube and conduit need a higher TPI, while thicker sections need a lower TPI, which clears swarf better and cuts faster but leaves a rougher edge.

    Power tool industry safety guidance adds that when cutting metal you should choose a blade that keeps at least three teeth in the material at all times. Fewer than three teeth can snag and break, although a tooth that is too fine will slow the cut. Blades often carry a tooth range as two numbers, and the pack or blade marking shows what it is meant for.

    Why do my blades keep bending, snapping or overheating?icon-minus-redicon-plus-red

    Industry safety guidance says a dull blade produces excessive heat and makes cutting difficult, which leads to forcing the saw. A build-up of sap or pitch on the blade, a blade without enough set or clearance, and unguided cuts can all overheat it, and overheating can warp a blade.

    Blades can also break if the shoe is not held firmly against the work, if the workpiece moves, or if the wrong blade is used for the job, so clamp the work and use the blade the saw maker recommends. Make sure the blade clamp is tight and the clamping area is clean, as swarf and dust can stop the blade being held securely.

    What safety precautions should I take when using a reciprocating saw?icon-minus-redicon-plus-red

    Power tool industry guidance says to clamp the workpiece securely and never hold it by hand or across your leg, hold the saw firmly with both hands, and firmly position the shoe on the work before starting, keeping it in contact throughout the cut. Check what is behind the workpiece for hidden pipes or wiring before you cut.

    Check the blade before each use and never use a bent, broken or warped blade. The blade and clamp can be hot straight after cutting, so avoid contact until they cool, and unplug the saw or remove the battery before changing blades or moving to another workstation. Follow the saw maker's instructions and wear eye protection as your risk assessment requires.

    How do I cut thin sheet or tube without the blade grabbing?icon-minus-redicon-plus-red

    Use a finer-pitch blade so that at least three teeth are in the material at all times. Industry guidance warns that fewer than three teeth in the cut cause snagging and breakage.

    Small or thin material can flex or vibrate with the blade and cause loss of control, so clamp it securely, support it close to the cut, and keep the shoe firmly in contact with the work. Let the blade reach full speed before it touches the workpiece, because the saw can chatter if the blade is slow at the start of the cut. A coarse blade tends to snatch at thin metal.

    Shop Similar Categories