WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

FEIN Nibblers & Shears

FEIN nibblers and shears are the perfect combination of performance and value.

FEIN Nibblers & Shears FAQs

Practical answers on choosing, using and looking after cordless nibblers and sheet metal shears.

Should I choose a nibbler or shears for cutting sheet metal?icon-minus-redicon-plus-red

It depends on the cuts you make most. A nibbler works like a punch and die, removing small chips of metal as it moves, so it copes well with tight curves, cut-outs and profiled or corrugated sheet, and it usually leaves the surrounding sheet flat.

Shears cut with two blades that slide past each other. They are generally quicker for long straight cuts in thinner sheet and make no chips, but some types curl or bend the sheet on one side of the cut. If you do a mix of work, many fabricators keep one of each. Our team can help you choose.

How thick a sheet can a cordless nibbler or shear cut?icon-minus-redicon-plus-red

There is no single figure, because the rated thickness depends on the tensile strength of the material as well as the tool. Harder, stronger steel can only be cut in thinner sheet than mild steel, and soft metals such as aluminium can usually be cut a little thicker.

The maker publishes a capacity table for each model, usually listed against several tensile strength bands. Many nibblers also have a gauge groove on the die holder, and the rule is not to attempt material that will not fit into it. Always work within the table on your tool's data plate or in its manual, and treat the rating as a maximum rather than a target.

Can these tools cut stainless steel and aluminium?icon-minus-redicon-plus-red

Nibblers and shears of this type are normally intended for sheet steel and stainless sheet steel, but stainless is tougher, so the maximum thickness is lower than for mild steel. Check the capacity table for your model and expect more vibration and wear when cutting stainless.

Aluminium and other soft metals can be cut, usually in a greater thickness than steel, but the chips tend to stick to the punch and die. Lubricating the cutting line with oil, as your manual describes, helps reduce this. Keep the cutting area free of other metals so you do not contaminate stainless sheet with steel particles.

How do I cut curves and internal cut-outs with a nibbler?icon-minus-redicon-plus-red

Nibblers are the usual choice for curves because the cutting head is compact and the sheet is not forced to one side. Every model has a minimum cutting radius, so check the manual for the tightest curve it will follow, and move the tool gently in the cutting direction rather than pushing hard.

For an internal cut-out you normally cannot start at an edge. Drill or punch a starting hole large enough for the cutting head to fit into, then nibble outwards to your marked line. Mark the line clearly and use the notch or cutting line indicator on the die holder to follow it.

What is the best way to cut corrugated or profiled sheet?icon-minus-redicon-plus-red

A nibbler is generally recommended for corrugated, trapezoidal and other profiled sheet, because it can follow the ridges and valleys without bending the profile out of shape. Shears can struggle where the sheet changes direction.

Support the sheet so it does not flex or rattle as you cut, and clamp it where you can. The cutting edges leave sharp burrs on profiled sheet, so wear cut-resistant gloves and take care when handling off-cuts. Cutting with a tool designed for the job also avoids the heat and coating damage that an abrasive cutting wheel can cause to galvanised or painted sheet.

What is the difference between slitting shears and sheet metal shears?icon-minus-redicon-plus-red

Both cut with blades, but they work differently. Slitting shears take out a thin strip as they go, which keeps the sheet flat and the edge clean, and they are generally used on thinner sheet. Sheet metal shears slice straight through the sheet, usually handle somewhat thicker material and cut long straight lines quickly, but they tend to bend or curl the sheet on one side of the cut.

Slitting shears are the better choice where flatness and a tidy edge matter, such as visible panels or ducting. Check each tool's rated thickness for the material you use.

Technical data ABLS 18 1.6 E AS ABSS 18 1.6 E AS ABLK 18 1.3 CSE AS ABLK 18 1.6 E AS 
Strokes (rpm) 2,200 - 3,500 2,200 - 3,500 1,200 - 6,500 850 - 1,350
Cutting speed (m/min) 6 - 9 5 - 8 1.9 1.5 
Steel up to 400 (N/mm²) 1.6 1.6 1.3 1.6 
Steel up to 600 (N/mm²) 1.2 1.2 0.8 1.0 
Steel up to 800 (N/mm²) 1.0 0.8 0.6 0.7 
Non-ferrous metals up to 250 (N/mm²) 2 2 2 2.5 
Cutting width (mm)  - 5 4 5  
Rad. of smallest curve (mm) 15 48 15 (IN) / 20 (OUT) 30 (IN) / 35 (OUT)
Weight (kg) 1.44  1.24 1.68 1.71