WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

FEIN ABAS 18-63 AS Saw Blades

FEIN ABAS 18-63 AS Saw Blades FAQs

Straight answers on choosing, running in and looking after bi-metal blades for portable metal-cutting band saws.

What is a bi-metal band saw blade and why is it used for cutting metal?icon-minus-redicon-plus-red

A bi-metal blade combines two steels. The teeth are made from high-speed steel, which stays sharp even when it gets hot, and they are joined to a tougher, more flexible steel body that can bend round the wheels of the saw without cracking.

That mix is why bi-metal blades are the usual choice for steel, stainless and other metals in a portable band saw. A plain carbon-steel blade can cut softer metals, but it tends to dull quickly once it heats up. Always check the blade type against the saw's manual and the material you are cutting.

How do I choose the right number of teeth per inch for the metal I am cutting?icon-minus-redicon-plus-red

The usual rule is that enough teeth should be in the cut at the same time to support the metal as the blade passes through it. Most guides give a baseline of around five to seven teeth in the cut, and some accept as few as three as a minimum.

In practice that means a finer pitch (more teeth per inch) for thin sections and a coarser pitch (fewer teeth per inch) for thick or solid sections. Too coarse and teeth can chip and the blade can bounce; too fine and the chips can overload the gaps between the teeth. Treat any chart as a starting point and check the blade maker's selection guide.

Which pitch should I use for thin-wall tube, angle and sheet?icon-minus-redicon-plus-red

For thin sections, the thickness of the wall matters, not the overall size of the tube or profile. A thin wall generally needs a finer pitch so that several teeth are always engaged and none of them drops into the open hollow and catches.

If you move up to a thicker or solid section, switch to a coarser blade. A fine blade used on thick material tends to fill its tooth gaps with swarf, which slows the cut and overheats the blade. When a job mixes thin and thick sections, a variable-pitch blade is often the more forgiving compromise.

How do I break in a new blade?icon-minus-redicon-plus-red

New teeth have a very sharp edge that can chip easily. Breaking the blade in lets that edge wear to a fine radius that holds up under cutting forces, and the blade then usually cuts straighter and lasts longer.

In general, start the first cuts with noticeably lighter feed pressure than normal, keep the cut steady without vibration, and raise the pressure gradually over several cuts until you reach the normal rate. Softer metals usually allow a bigger reduction at the start than harder ones. The exact amount depends on the blade, the metal and the saw, so follow the blade maker's instructions.

What is the difference between a variable-pitch and a constant-pitch blade?icon-minus-redicon-plus-red

A constant-pitch blade has evenly spaced teeth, which suits uniform sections and non-ferrous metals. A variable-pitch blade alternates the spacing between teeth, which spreads the load and generally reduces vibration and noise.

For general work on mixed sections such as tube, pipe and profiles, variable pitch is usually the more forgiving choice and is often described as the better all-rounder. Whichever you choose, match the blade to the job rather than relying on one blade for everything.

Why does my blade stop cutting properly in stainless steel?icon-minus-redicon-plus-red

Stainless steel can harden at the cut face if the blade rubs instead of cutting. This usually happens when the feed pressure is too light, the blade is already dull, the blade has too fine a pitch or the speed is too high. Once the surface has hardened, even a sharp blade struggles.

Use a blade made for the material, keep the feed steady and firm enough that the teeth bite and produce proper chips, and avoid pausing with the blade running against the work. Follow the blade maker's recommended feeds and speeds, and use cutting fluid if the maker advises it.