WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

FEIN Magnetic Vices

FEIN Magnetic Vices FAQs

Answers to common questions about magnetic vices and their jaws, magnets and welding plates, from how well they hold to using them safely.

What is a magnetic vice and what is it used for?icon-minus-redicon-plus-red

A magnetic vice is a clamping vice that sits on a strong magnetic base, so it can be fixed to a steel surface such as a steel plate, a fabrication table or a machine base without bolts or G-clamps. The jaws then hold the workpiece, which might be a pipe, bar or section being drilled, cut, ground or tack welded.

The magnet and the jaws do different jobs: the magnet keeps the vice in place, and the jaws grip the work. Always check in the manufacturer's manual which surfaces, loads and jobs the vice is designed for.

What affects how firmly a magnetic base will hold?icon-minus-redicon-plus-red

A published holding figure is a best-case value, measured with the magnet in direct, flat contact with thick, ground, low-carbon steel. In real use the hold falls if the steel is thin, if the surface is rough, curved, rusty, painted or dirty, or if the magnet is not fully in contact with the steel.

Any layer between the magnet and the steel acts like an air gap, and the hold drops steeply as the gap grows. For the best result, clean the base and the surface, put the vice on thick, flat steel and always follow the manufacturer's instructions for the model you have.

Does the thickness of the steel under the vice matter?icon-minus-redicon-plus-red

Yes. A magnet needs enough steel under it to carry its full magnetic flux. On thin sheet some of the flux passes straight through, so the magnet holds noticeably less than its rated figure. Thin steel is a common reason a vice feels weaker than expected.

For thin material, use a thicker steel plate underneath as a backing surface, add fixed stops so the vice cannot slide, and check the manual for the minimum steel thickness the manufacturer recommends. Do not rely on the magnet alone when the support is thin.

Can I use a magnetic vice on a painted, rusty or rough surface?icon-minus-redicon-plus-red

You can try, but expect less holding power. Paint, rust, mill scale, dirt and rough or uneven surfaces all create tiny air gaps between the magnet and the steel, and even a thin gap reduces the hold. A rough surface can hold far less than a clean, flat, ground one.

Clean the surface and remove loose swarf and spatter before switching on or placing the vice. If you must work on a coated or uneven surface, treat the rated holding figure as unreliable, test the hold carefully before applying load and use extra support or stops if in doubt.

Will a magnetic vice resist sideways force when I drill or cut?icon-minus-redicon-plus-red

Not as strongly as it resists a straight pull. Most real loads on a vice are sideways or twisting, and magnet resistance to sliding depends on friction, so it is usually only a fraction of the straight-pull figure. Drilling, sawing and grinding all create sideways and twisting forces.

Keep cutting loads light, support the vice against fixed stops where you can, and never rely on the magnet alone to resist a heavy sideways force. Follow the maker's guidance for the job, and stop immediately if the vice shifts or creeps.

How do I hold round pipe or bar securely?icon-minus-redicon-plus-red

Round work touches the vice along a line rather than across a flat face, so it is harder to hold than flat plate. Use V-shaped or prismatic jaws made for round work, make sure the pipe or bar sits fully in the V, and tighten evenly. Jaws that are too small, too large or worn can let the work rotate or slip.

For longer lengths, support the free end so the weight does not lever against the jaws. Do not over-tighten thin-walled pipe, because it can distort. Check the manual for the diameter range the jaws are designed for.