WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

FEIN Premium Angle Grinders

  • Excellent power-to-weight ratio
  • Brushless motor

Fully enclosed FEIN PowerDrive motor protects from aggressive ceramic and mineral dust. All CG 15 are variable speed allowing for optimum performance in many applications and on multiple materials.

For technical data for each grinder, please see below.

FEIN Premium Angle Grinders FAQs

Answers to common questions about choosing, using and looking after a premium brushless angle grinder.

Does the disc have to be rated for the grinder's speed?icon-minus-redicon-plus-red

Yes. The rated speed of any disc or accessory must be at least equal to the maximum speed marked on the grinder. A disc that is rated lower than the grinder can run at can break up in use, and that is a serious injury risk.

With a variable-speed grinder, check the highest no-load speed on the data plate, not the speed you plan to use, and compare it with the maximum operating speed printed on every disc. Never fit a disc whose rating is lower, and do not guess if the marking has worn off.

If you are unsure, check the grinder manual and the disc maker's instructions, or ask our team.

What is kickback and how do I reduce the risk?icon-minus-redicon-plus-red

Kickback is a sudden reaction when a spinning disc is pinched or snagged. It throws the grinder in the direction opposite to the disc's rotation at the point where it caught, and it can happen very quickly.

To reduce the risk, keep a firm two-handed grip with the side handle fitted, and stand so your body is out of the line the grinder would travel. Keep your hand away from the spinning disc, and take care at corners and sharp edges where the disc can bounce or snag.

Some grinders also have electronic monitoring that reacts to a sudden snag, but treat that as a back-up and never as a substitute for good technique. Check the manual for how your model behaves.

How should I fit and test a new disc?icon-minus-redicon-plus-red

Unplug the grinder first, then check that the disc is the right type and size, and that it is not chipped, cracked or worn out. Do not use a damaged disc. Fit it with the flanges and nut the maker specifies, the right way round and without improvised washers, and tighten it with the key supplied. Follow both the grinder manual and the disc instructions.

Once fitted, with the guard in place, run the grinder at full no-load speed for about a minute with yourself and anyone nearby standing out of line with the disc. If there is any wobble, vibration or noise, stop and fix the cause before starting work.

Do not lay the grinder down until the disc has come to a complete stop.

How can I reduce hand-arm vibration when I grind a lot?icon-minus-redicon-plus-red

Regular grinding can expose your hands and arms to vibration, which over time may cause lasting nerve and circulation problems. The HSE advises choosing the lowest-vibration tool that does the job properly, comparing the vibration figures that makers publish, and keeping equipment well maintained.

Worn or damaged discs make the grinder work harder, so replace consumables such as grinding wheels when they are worn. Limit continuous time on the tool and take breaks where you can, rather than doing one long spell.

Avoid gripping the grinder harder than you need to. Your employer's risk assessment should set sensible limits for your work.

Why must the guard stay on, and can I swap to a smaller guard?icon-minus-redicon-plus-red

The guard is there to contain fragments if a disc breaks, to protect you from accidental contact with the disc, and to deflect sparks. It must be firmly attached and turned so that as little of the disc as possible faces you. Never work without it.

Never remove it to fit an oversized disc. Some premium grinders accept a smaller guard so that a smaller-diameter disc can be used, but only if the grinder maker says the combination is allowed. Check the manual, and make sure the disc size and its rated speed match the grinder and the guard.

If you cut with a grinder, the standard grinding guard is generally not suitable. Use the cutting guard or adapter the maker recommends.

Should I use a flap disc, a grinding disc or a cutting disc?icon-minus-redicon-plus-red

A grinding disc is a rigid bonded wheel for heavy stock removal, such as taking down weld runs or thick scale, but it leaves a rougher finish and creates more heat. A flap disc is made of overlapping abrasive flaps and can grind and finish in one step, with a smoother result, less heat and less vibration. Flat flap discs suit flat surfaces and angled ones suit steeper angles and contoured work.

A cutting disc is thin and designed only for straight cuts. Side force can make it flex and fail, so never use it for grinding and never lever or twist it in the cut.

Whichever disc you pick, match its rated speed and size to the grinder.

Technical data LG 24-230D CG 15-125 BL CG 15-125 BL INOX  CG 15-125 BLP  CG 15-125 BLP INOX
Grinding disc diameter (mm) 230  125 125 125 125
Input (W) 2400  1500 1500 1500 1500
Output (W) 1600  1050 1050 1050 1050
No load speed (rpm) 6600 3800 - 9000 2800 - 7000 3800 - 9000 2800 - 7000
Overload protection N  Y Y Y Y 
Kickback monitoring N  Y Y Y Y 
Brake function N  Y Y Y Y 
Cable length (m) N 4 4 4 4
Weight (kg) 6.1  2.4 2.4  2.4 2.4