WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

FEIN Rotary Hammer Drills

  • Compact and powerful
  • Versatile multi-function

    FEIN rotary hammer drill ideal for drilling in concrete up to 20mm using SDS-PLUS fitting.

  • FEIN Rotary Hammer Drills FAQs

    Straight answers on choosing, using and looking after a rotary hammer drill for drilling concrete and masonry.

    What is the difference between a rotary hammer and an ordinary hammer drill?icon-minus-redicon-plus-red

    A hammer drill gets its hammering from two ridged discs that ratchet against each other, giving very fast, shallow blows. A rotary hammer uses a piston that drives a striker onto the back of the bit, so the blows are slower but much heavier. That is why a rotary hammer is the usual choice for larger holes in concrete, for drilling through reinforcing bar and for light breaking work.

    A hammer drill is lighter and fine for small holes and occasional jobs, and many can have the hammering switched off for wood or metal.

    What does SDS-plus mean, and how do I choose between SDS-plus and SDS-max?icon-minus-redicon-plus-red

    SDS is a type of bit shank. The bit slides into a spring-loaded chuck and locks in place without a chuck key, and it is free to move back and forth so the hammer blows reach the cutting end. The tool and the bits have to match: SDS-plus is the lighter system for small to medium holes, while SDS-max is the larger system for bigger holes and heavier work.

    A compact machine that takes SDS-plus bits is normally the right size for anchor holes and general drilling in concrete and brick. Check the hole sizes the maker lists for your model.

    What is hammer-only mode used for?icon-minus-redicon-plus-red

    Most rotary hammers have a setting where the bit stops turning and only the hammering is active. It is used with chisels and similar tools for light demolition, such as removing tiles, chasing out a small channel or knocking off render.

    Drilling uses the rotation-plus-hammer setting. Some models also have a position that locks the chisel at a chosen angle, so look at the selector markings and the manual for what your model provides and use the right setting for the accessory in the chuck.

    Can I use a rotary hammer to drill steel or wood?icon-minus-redicon-plus-red

    Generally no. A rotary hammer is built for masonry and concrete, and it is normally not suited to wood or metal. The hammering action is wrong for those materials and the SDS chuck does not suit ordinary round-shank twist drills unless you use a specially made adaptor, and then only as the maker allows.

    For steel, stainless steel and aluminium, use a drill designed for metal with a suitable twist drill or cutter. If you need to drill through reinforcing bar buried in concrete, use a bit intended for it and follow the manual.

    Why is drilling concrete a dust hazard, and what should I do about it?icon-minus-redicon-plus-red

    Concrete and similar materials can contain silica, and the dust from drilling can contain very fine crystalline silica. Breathing it in can cause serious and permanent lung diseases, including silicosis, chronic obstructive pulmonary disease and lung cancer. The HSE treats drilling concrete with hand-held rotary tools as work that needs good dust control.

    Control the dust at the source with a dust collector or extraction attached to the drill, wear suitable respiratory protective equipment where your risk assessment calls for it, and limit who is nearby. Ask the HSE or your safety adviser for the guidance that applies to your job.

    How should dust extraction be used with a drill like this?icon-minus-redicon-plus-red

    Dust extraction works best when it is part of the setup, not an afterthought. For short or occasional drilling, a dust collector that fits over or onto the drill can capture dust at the hole. For regular drilling, an on-tool hood connected to a suitable industrial extractor with the correct hoses and connections is normally expected.

    Check that the extraction is switched on and working, that hose connections are tight, and that the collection bag or container is emptied regularly. The larger the hole, the better the capture needs to be. Use extraction equipment of the class your risk assessment requires.