WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

FEIN Pipe Saws

  • Cut pipes and profiles to length.

  • Diameter of up to 440mm.

    Optimum cutting speed with minimal wear for pipes of up to 440 mm in diameter.

  • FEIN Pipe Saws FAQs

    Answers to common questions about air-powered pipe saws for cutting pipe and tube to length on site or in the workshop.

    How do I get a square cut and make the blade last longer?icon-minus-redicon-plus-red

    Support and guide the blade. A blade guide that spans the pipe steadies the blade so it does not whip or vibrate, and makers of air saws say this extends blade life, squares the cut and helps avoid accidental blade breakage. A chain or clamp that locates the saw on the pipe helps keep the cut at right angles.

    Clamp the pipe or the tool securely, let the blade cut at its own pace rather than forcing it, and support the pipe so the cut does not pinch the blade near the end. A pinched or twisted blade wears quickly and can break.

    Do I need to disconnect the air before changing a blade?icon-minus-redicon-plus-red

    Yes. Disconnect the tool from the air supply and make sure pressure is relieved from the hose and tool before you change a blade or any attachment, make adjustments or put the tool down. Safe-use procedures for pneumatic tools give this instruction because it stops the saw starting accidentally while your hands are near the blade.

    When reconnecting, make sure the trigger or lock is in the off position first. Wear eye protection and any other protective equipment your risk assessment calls for whenever the tool is running, and keep other people clear of the cutting area.

    How do I use air hoses and couplings safely with a pipe saw?icon-minus-redicon-plus-red

    Check hoses and fittings before use for cuts, bulges, wear and loose connections, and never set the supply above the maximum pressure stated for the tool or the hose. The HSE's compressed air guidance names over-pressurisation as the major hazard with compressed air equipment.

    A hose that comes off under pressure can thrash about. Industry guidance recommends hose restraints (whip checks) on flexible hoses, particularly larger-bore or high-pressure ones, and safety couplings that vent downstream air before they part are widely used. Keep the hose clear of the blade and cutting area, and follow the tool maker's instructions and your own risk assessment.

    Why is my air saw running slowly or losing power?icon-minus-redicon-plus-red

    The usual cause is not enough air reaching the tool while it is working. A hose with too small a bore or too great a length loses pressure through friction, and kinks, restrictive couplings, filters and other accessories each add to the loss. Pressure read with the tool idle can look correct and then fall sharply once the saw is running, so it is better to judge it at the tool inlet under load.

    Also consider a compressor that cannot keep up with the tool's air consumption, a regulator set too low, or water and dirt in the filter. If the supply is sound, a worn blade or a tool that needs servicing may be the cause. Check the manual for the air pressure and flow the tool needs.

    Does an air saw need a filter, regulator and lubricator?icon-minus-redicon-plus-red

    Air tool makers generally recommend all three. A filter keeps water and particles out of the air motor, which reduces wear and helps the tool hold its power and speed over time. A regulator lets you set the working pressure, and one regulator per tool is a common recommendation. A lubricator meters a little oil into the air to protect the motor.

    They are normally fitted in that order, close to the tool. Not every tool needs added oil, so use the lubrication method and the oil type given in the tool's manual, and follow the maker's service instructions.

    Can an air-powered pipe saw cut stainless steel, and how do I get the best result?icon-minus-redicon-plus-red

    Many are used on stainless steel pipe, provided the blade is suitable for stainless and the maker's wall thickness and diameter limits are respected. Stainless is difficult to saw: trade guidance says it usually calls for a lower blade speed with a firm, steady feed so the teeth bite and cut instead of rubbing, and a rubbing blade work-hardens the surface and dulls quickly.

    Change the blade as soon as it stops cutting freely rather than pushing harder. To avoid contaminating the stainless and harming its corrosion resistance, do not use tools, brushes or discs that have been used on carbon steel, and keep carbon steel dust and offcuts away from the stainless.