WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

ARC WELDING

Arc Welding FAQs

Straight answers to the questions people ask most when choosing and using manual metal arc (stick) welding equipment.

What is stick (MMA) welding and what is it best for?icon-minus-redicon-plus-red

Stick welding, also called manual metal arc or MMA, uses a coated metal rod (the electrode) held in a holder. The arc melts the rod and the parent metal together, and the coating burns off to form a gas shield and a layer of slag over the weld. Because the shielding comes from the rod itself, no gas bottle is needed.

It copes well with outdoor work, wind, rusty or dirty steel, site repairs and heavier fabrication, and the equipment is simple and robust. It is less neat than MIG or TIG on thin sheet, and every weld needs the slag chipping off afterwards.

How do I choose an arc welder?icon-minus-redicon-plus-red

Start with the thickness of metal you weld and the rods you want to use, because that sets the current the machine must be able to supply. Then check your power supply: smaller machines run from a single-phase mains supply, while larger ones need three-phase. Some compact machines will also run from a reduced-voltage site supply.

Look at the duty cycle too, which tells you how long the machine can weld at a given current before it needs to rest. Modern inverter machines are light, efficient and easy to carry. Older transformer machines are heavy but very hard-wearing. Our team can help you match a machine to your work.

Which electrode should I use?icon-minus-redicon-plus-red

It depends on the metal and the job. Rutile electrodes are the general-purpose choice for mild steel: they strike easily, run smoothly and give a tidy bead. Basic (low-hydrogen) electrodes make stronger, tougher welds and are used on thicker, structural or higher-strength steel, but they are fussier to use and must be kept dry. Cellulosic electrodes give deep penetration and are mainly used on pipe.

There are also electrodes for stainless steel, cast iron repair, hard-facing and other special jobs. Always match the electrode to the metal and check the maker's recommendations on the pack.

What electrode size and current setting should I use?icon-minus-redicon-plus-red

Electrode diameter is chosen mainly by the thickness of the metal and the type of joint. Thin material needs a thin rod and a lower current, while thicker material and wide joints need a larger rod and a higher current. A thicker rod needs more current to melt properly.

The pack or the maker's data sheet gives a recommended current range for each size. Start in the middle of that range and adjust. Too low and the rod sticks and the bead sits on top. Too high and the rod overheats and burns, the coating can crack and the weld spatters and undercuts.

What protective equipment do I need for arc welding?icon-minus-redicon-plus-red

The arc is intensely bright and gives off ultraviolet and infrared radiation that can burn your eyes and skin in seconds, so you need a proper welding helmet or hand shield with a filter of the right shade for the current you are using. Auto-darkening helmets are popular, but must be suitable for stick welding. Also wear welding gloves, flame-resistant clothing covering your arms and neck, and safety boots.

Welding fume is harmful, so work with good ventilation or extraction, and use respiratory protection where your risk assessment says you need it. Keep the HSE guidance and the manufacturer's instructions to hand.

Why do electrodes need drying, and what does a rod oven do?icon-minus-redicon-plus-red

Electrode coatings absorb moisture from the air. In basic (low-hydrogen) electrodes especially, that moisture puts hydrogen into the weld, which can cause porosity and cracking, particularly on thicker or higher-strength steel. Damp rods also run badly and give a rough, spattery arc.

Sealed packs are fine until you open them. After that, rods are normally kept warm in a holding oven and taken out a few at a time. Rods that have been left out too long can be re-baked in an oven, but only to the maker's instructions, because the temperature and time depend on the electrode type.