SHOW PRICES INCLUDING VAT
Trustpilot
Click to visit the Rapid Blog - Supporting welders every step of the way
0Your Basket : £ 0.00
WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
428337 Hypertherm HyAccess Extended Cutting & Gouging Consumable Kit, for Powermax 30, 30/33XP & 45
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 428337  

    Hypertherm HyAccess Extended Cutting & Gouging Consumable Kit, for Powermax 30, 30/33XP & 45
    428337

    Click here to see what's included
    £158.40  EX VAT
    SSP Suggested Selling Price = £198.00  YOU SAVE £39.60
     Buy in 3 easy interest free payments of £52.80† with

    Patented HyAccess consumables provide the extra reach needed when cutting or gouging in hard-to-reach or confined spaces. HyAccess consumables extend over 3 inches beyond standard consumables. The unique design allows for better visibility and accessibility for working on challenging cutting locations such as corners and channels. HyAccess™ consumables for cutting and gouging are currently available for Powermax45® and Powermax 30/33XP systems (Powermax 30 systems with 220670 swirl ring).

    Kit Contents

    Part # Description Qty
    420144 Nozzle/Shield - Cutting 1
    420147 Nozzle/Shield - Gouging 1
    420148 Retaining Cap 1
    420137 Electrode 2
    220670 Swirl Ring 1
      Total 6 parts

    Product Details

    Related Items

    Powermax 125 Machine Systems FAQs

    Straight answers to the questions people ask most when choosing a top-end plasma system for mechanised cutting.

    How does torch height control work?icon-minus-redicon-plus-red

    A height controller reads the arc voltage and raises or lowers the torch to keep a constant gap between torch and plate. This keeps cut quality and bevel angle consistent as plate warps, and extends consumable life.

    It needs a stable voltage signal from the plasma system, so check that your system and controller support each other, and test on scrap plate first.

    How long should the torch lead be?icon-minus-redicon-plus-red

    It should reach the whole travel of the gantry or carriage without being stretched or snagged. A lead that is too short limits movement and wears quickly; a lead that is too long adds clutter.

    Use a drag chain or support on larger tables, and avoid coils, tight bends and pinch points.

    What supply and air do I need?icon-minus-redicon-plus-red

    The data plate and manual give the input voltage, number of phases and current drawn. Higher-power machine systems commonly need a three-phase supply, but this varies, so do not assume. The supply, protective device and cabling must suit the figures on the plate and should be installed or checked by a qualified electrician.

    The system also needs a good flow of clean, dry compressed air at the pressure and flow rate stated in the manual. Use a properly sized compressor, filter and moisture separator, with a dryer for heavy use, and check pressure with air flowing.

    How do I get a clean, square edge?icon-minus-redicon-plus-red

    Edge quality depends on current, travel speed, stand-off height, consumable condition and air quality. Use the maker's cut chart as a starting point, then adjust on scrap plate. Slow speeds leave dross and fast speeds leave it trailing behind.

    Remember that plasma edges have a natural slight angle, and worn consumables make it worse. Replace them early.

    See all 6 questions for this category

    Shop Similar Categories